10S 36V 20A Hardware BMS for E-scooter

This FY•X high quality 10S 36V 20A Hardware BMS for E-scooter is a protective plate solution specially designed by Huizhou Feiyu New Energy Technology Co., Ltd. for 10-cell battery packs for electric bicycles and scooters; it can be applied to lithium batteries with different chemical properties, such as lithium ion, lithium polymer, etc. The protection board has strong load capacity and the maximum continuous current can be 20A.

FY•X high quality 10S 36V 20A Hardware BMS for E-scooter Functional characteristics

● Ten battery cells are protected in series;

● Charging and discharging voltage, temperature, overcurrent and other protection functions;

● Low power consumption.

Physical reference picture

Figure 1: BMS front view

Figure 2: Physical picture of the back of BMS

Electrical Characteristic (Ta = 25 ℃.)

BMS principle block diagram  

Figure 7: Protection principle block diagram

PCB and dimensional structure diagram

Figure 8: Motherboard top-level wiring diagram

Figure 9: Motherboard bottom wiring diagram

Figure 10: Dimensions 124.6*38 Unit: mm Tolerance: ±0.5mm

Protection board thickness: less than 10mm (including components)  

Port Definition

Figure 11: Protection board wiring diagram

Port definition description：

Figure 12: Schematic diagram of battery connection sequence

Matching wire drawings (depending on whether the wire is matched with the order)

DIP material\Wire\11PIN\1.25mm\3302#26A (Special for Fish10S001-1) with buckle terminal glue\Yuke\ROHS

Precautions for connecting the protective board and the battery core

Warning: When connecting the protective plate to the battery cells or removing the protective plate from the battery pack, the following connection sequence and regulations must be followed; if operations are not performed in the required order, the components of the protective plate will be damaged, resulting in the protective plate being unable to protect the battery. core, causing serious consequences.

Preparation: According to the definition shown in Figure 11, connect the corresponding voltage detection cable to the corresponding battery core. Please pay attention to the order in which the sockets are marked.

Steps to install protective board:

Step 1: Weld the P- and C- wires to the corresponding positions of the protection board without connecting the charger and load.

Step 2: Connect the negative pole of the battery pack to B- of the protection board;

Step 3: Connect the positive terminal of the battery pack to B+ of the protection board;

Step 4: Connect the battery pack and battery rows to J1 of the protection board;

Steps to remove the protective plate:

Step 1: Disconnect all chargers\loads

Step 2: Unplug the battery pack’s battery strip connector J1;

Step 3: Remove the connecting wire connecting the positive electrode of the battery pack from the B+ pad of the protective plate

Step 4: Remove the connecting wire connecting the negative electrode of the battery pack from the B- pad of the protective plate

Additional notes: Please pay attention to electrostatic protection during production operations.

BOM list of main components

Note: If SMD transistors and MOS tubes are out of stock, our company may replace them with other models of similar specifications.

Ordering information

1 Feiyu company logo;

2 Protection board model - (This protection board model is Fish10S001, other types of protection boards are marked, there is no limit to the number of characters in this item)

3. The number of battery strings supported by the required protection board - (this model of protection board is suitable for 17S battery packs);

4 Charging current value - 2A means the maximum support for continuous 2A charging;

5 Discharge current value - 20A means the maximum support for continuous charging is 20A;

6 Balance resistance size - fill in the value directly, for example, 100R, then the balance resistance is 100 ohms;

7 Battery type - one digit, the specific serial number indicates the battery type as follows;

8. Communication method - one letter represents a communication method, I represents IIC communication, U represents UART communication, R represents RS485 communication, C represents CAN communication, H represents HDQ communication, S represents RS232 communication, 0 represents no communication, product UC Represents UART+CAN dual communication;

9. Hardware version - V1.0 means the hardware version is version 1.0.

10.The model number of this protection board is: WH-Fish10S001-10S-2A-20A-0-4-0-V1.1. Please place the order according to this model number when placing bulk orders.

Additional notes:

1. When performing charge and discharge tests on the battery pack with the protective board installed, please do not use a battery aging cabinet to measure the voltage of each cell in the battery pack, otherwise the protective board and battery may be damaged. .

2. This protection board does not have a 0V charging function. Once the battery reaches 0V, the battery performance will be severely degraded and may even be damaged. In order not to damage the battery, the user should not charge the battery for a long time (the battery pack capacity is greater than 15AH, and the storage exceeds 1 Months) When not in use, it needs to be charged regularly to replenish the battery; when in use, it must be charged in time within 12 hours after being discharged to prevent the battery from being discharged to 0V due to self-consumption. Customers are required to have an obvious sign on the battery casing that the user regularly maintains the battery.

3. This protection board does not have reverse charging protection function. If the polarity of the charger is reversed, the protection board may be damaged.

4. This protective board shall not be used in medical products or products that may affect personal safety.

5. Our company will not be responsible for any accidents caused by the above reasons during the production, storage, transportation and use of the product.

6. This specification is a performance confirmation standard. If the performance required by this specification is met, our company will change the model or brand of some materials according to the order materials without further notification.

Note: After your company receives the prototype and specifications, please reply promptly. If there is no reply within 7 days, our company will regard your company as having recognized the specifications and send the prototype. If your order exceeds 50 PCS, you need to sign back the acknowledgment letter. If you do not sign back, our company will also regard your company as having approved this specification and send the sample machine. The pictures in the specification are of general-purpose models, which may be slightly different from the sample delivered. Feiyu reserves the right of final interpretation of this specification.

DISCLAIM:

In order to improve the design or performance and to supply the best possible products, Wenhong reserves the right to make changes to the products contained in this data sheet. Wenhong assumes no responsibility for the use of any circuits shown in this data sheet, conveys no license under any patent or other rights, and makes no claim that the circuits are free from patent infringement. Applications for any devices shown in this data sheet are for illustration only and Wenhong  makes no claim or warranty that such applications will be suitable for the use specified without further testing or modification.

LIFE RELATED POLICY:

In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detection and correction, redundancy and back-up features to prevent such an occurrence.

Wenhong’s products are not authorized for use in critical components in life support devices or systems.

1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.

2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.